Great-dane Chariot GDRZ25KAE Manuel d'utilisateur

c WARNING: The Engine Exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects or other reproducti

Operating - 7OPERATINGTesting Park Brake Safety Switch1. Operator must be seated in the seat (seat safety switch engaged).2. Move control levers to ne

Operating - 8OPERATINGseconds.• Repeat the procedure if necessary.9. Let the engine run at half-speed position for several minutes to warm up before o

Operating - 9OPERATING3. Depress and hold the mower deck lift/lower pedal (A) and release the transport position lock lever (C).4. Release the mower d

Replacement Parts - 10REPLACEMENT PARTSReplacement PartsPartsWe recommend Great Dane quality parts available at your Great Dane dealer.Part numbers ma

Service Intervals - 11SERVICE INTERVALSService IntervalsServicing Your MachinePlease use the following timetables to perform routine maintenance on yo

Service Lubrication - 12SERVICE LUBRICATIONService LubricationGreaseUse a general all-purpose grease with an NLGI grade No.2 rating.Wet or high speed

Service Engine - 13SERVICE ENGINEService EngineAvoid FumesEngine Oil Use oil viscosity based on the expected air temperature range during the period b

Service Engine - 14SERVICE ENGINECheck and clean air filter elements at the intervals recommended in the Service Intervals section. See the engine man

Service Transmission - 15SERVICE TRANSMISSIONService TransmissionAvoid FumesTransmission OilUse only Quaker State® 5W-50 or Mobil-1® 15W-50 all synthe

Service Transmission - 16SERVICE TRANSMISSIONMX92445. Move control levers to neutral position. The wheels should stop rotating. If the wheels continue

IntroductionINTRODUCTIONIntroductionUsing Your Operator’s ManualThis manual is an important part of your machine and should remain with the machine wh

Service Transmission - 17SERVICE TRANSMISSION1. Park machine safely. (See Parking Safely in the Safety section.)2. Check hydraulic oil level. Adjust a

Service Mower - 18SERVICE MOWERService MowerAdjusting Mower Level1. Park machine safely. (See Parking Safely in the Safety section.)2. Inflate drive (

Service Mower - 19SERVICE MOWERMX92854. Loosen the jam nut (B) on the link rod assembly, and turn the sleeve (C) until the blade height is 89 mm (3-1/

Service Mower - 20SERVICE MOWERChecking for Bent Mower Blades1. Park machine safely. (See Parking Safely in the Safety section.)2. Lower mower deck to

Service Mower - 21SERVICE MOWERM61830• Keep original bevel (A) when grinding.• Blade should have 0.40 mm (1/64 in.) cutting edge (B) or less.• Balance

Service Mower - 22SERVICE MOWER11.Install upper pulleys:• Side Spindles: Install pulley (C), spacer (B) and nut (A). Tighten nut to 80 N•m (60 lb-ft).

Service Electrical - 23SERVICE ELECTRICALService ElectricalWARNING: Battery posts, terminals and related accessories contain lead and lead components,

Service Electrical - 24SERVICE ELECTRICALapproximately halfway between bottom of filler neck (B) and top of plates (C).5. Add only distilled water if

Service Electrical - 25SERVICE ELECTRICALKohler Wiring SchematicMX9299A

Service Miscellaneous - 26SERVICE MISCELLANEOUSService MiscellaneousFilling Fuel TankUse regular grade 87 octane unleaded fuel.Add fuel stabilizer to

Table of ContentsTABLE OF CONTENTSAll information, illustrations and specifications in this manual are based on the latest information at the time of

Service Miscellaneous - 27SERVICE MISCELLANEOUSMX92243. Remove cap (A), cotter pin (B), castle nut (C), caster yoke and wheel assembly (D) and caster

Troubleshooting - 28TROUBLESHOOTINGTroubleshootingUsing Troubleshooting ChartIf you are experiencing a problem that is not listed in this chart, see y

Troubleshooting - 29TROUBLESHOOTINGElectricalMachine OperationMower If CheckStarter Does Not Work Or Will Not Turn Engine Park brake is not locked.PTO

Troubleshooting - 30TROUBLESHOOTINGBelt Slipping Debris in sheaves.Worn belt.Too Much Vibration Debris on mower deck or in sheaves.Damaged sheaves or

Storage - 31STORAGEStorageStoring SafetyPreparing Machine for Storage1. Repair any worn or damaged parts. Replace parts if necessary. Tighten loose ha

Assembly - 32ASSEMBLYAssemblyInstall Seat and Control Lever Handles1. Install seat on platform and secure using nuts provided in small parts bag.2. Co

Assembly - 33ASSEMBLYCheck Tire Pressure1. Check tires for damage. 2. Check tire pressure with an accurate gauge.3. Check that tires have equal pressu

Specifications - 34SPECIFICATIONSSpecificationsEngineNOTE: See engine manufacturer’s owner’s manual provided with your machine for engine specificatio

Index - 35INDEXIndexAAir Cleaner Elements, Replacing ... 13Air Cleaner Elements, Servicing ...

NotesNOTESNotes

Safety - 1SAFETYSafetyUnderstanding The Machine Safety Labels MIFThe machine safety labels shown in this section are placed in important areas on your

Service Record GD - 37SERVICE RECORD GDService Record GDRecord Service DatesEngine Oil and Filter ChangeLubricate MachineAir Cleaner Element Clean/Rep

Safety - 2SAFETYCAUTIONMX9295 MX9214• This product is designed for professional and commercial users.• Operation training is required.• Carefully read

Safety - 3SAFETY• Stop machine if anyone enters the area.• Never raise mower decks when blades are running.• If you hit an object, stop and inspect th

Safety - 4SAFETY• Drive across a hill - not up and down. If necessary, turn slowly and in the downhill direction. Do not shift to neutral and coast do

Safety - 5SAFETYdamage and vibration. Check connections regularly. Tighten loose connections.• Escaping fluid under pressure can penetrate the skin ca

Operating - 6OPERATINGOperatingDaily Operating Checklist❏ Test safety systems.❏ Check tire pressure.❏ Check fuel level.❏ Check engine oil level.❏ Remo